not really an issue, but some questions

[philippedc]

Hi, first many thanks for sharing this project. it is the only one I succeed to make working., as I'm trying to build a kind of baby monitor and I get many difficulties to make inmp441 working. I'm trying to get a loader audio channel.
(I use Arduino IDE version 1.8.16 with Expressif Sytems (ESP32) version 2.0.3)

There are not many information how to use i2s parameters, I have some questions, if I can get any answer to improve my knowledge:

• as I understand the i2s_read needs a signed 32 bits buffer, and you use unsigned 8 bits (byte). How is it possible ?
• where can I get information about the choose of DMA_BUF_COUNT vs DMA_BUF_LEN, several examples uses 8 / 64 instead of 2 / 1024, and I cannot understand why.
• is there a i2s_config keyword to increase audio sensibility ?

[philippedc]

I've found a solution. However the sound quality is quite ugly. But in fact the web audio transfer must be under 8 bits, so.... It is just good enough for a baby monitor.
The key is to convert the 32 bits (in fact 24 bits) microphone to 16 bits, and keep the MSB only to 8 bits.

` uint8_t buffer32[bufferSize];
uint8_t buffer16[bufferSize/4];
size_t bytesRead = 0;

while(true) {
if(!Audioclient.connected()) {
Serial.println("Audioclient disconnected");
break;
}
// Read audio data from I2S DMA
i2s_read(I2S_PORT, &buffer32, bufferSize, &bytesRead, 1000);

// convert 32 bits (in fact 24 bits inmp441) to 16 bits
// then truncated to 8 bits value for Audiclient web format
// Offset + 0 is always E0 or 00, so discard it.
// Offset + 1 is the LSB of the sample, but is just fuzz, discard it.
// https://esp32.com/viewtopic.php?t=15185
int samplesRead = bytesRead /4;
for(int i=0; i<samplesRead; i++) {
  uint8_t mid = buffer32[i*4 +2];
  uint8_t msb = buffer32[i*4 +3];
  uint16_t raw = (msb << 8) + mid;
  if( raw > 255 ) raw = 255;
  memcpy(&buffer16[i], &raw, sizeof(uint8_t));  //buffer16[i] = raw; 
}  // end of for

// Send audio data
if(samplesRead > 0) Audioclient.write(buffer16, samplesRead);

} // end of while`

[spawn451]

Hello @philippedc sorry been a while i didn't get here. I will check this out when I have some time.

[philippedc]

Hi @spawn451
in fact the result is much better like this:
int samplesRead = bytesRead /4;
for(int i=0; i<samplesRead; i++) {
//uint8_t mid = buffer32[i4 +2];
//uint8_t msb = buffer32[i4 +3];
//uint16_t raw = (msb << 8) + mid;
//if( raw > 255 ) raw = 255;
uint8_t raw = buffer32[i*4 +2];
memcpy(&buffer16[i], &raw, sizeof(uint8_t)); //buffer16[i] = raw;
} // end of for

// Send audio data
if(samplesRead > 0) Audioclient.write(buffer16, samplesRead);

Now the inmp441 is very sensitive, even too much. It is OK for a baby monitor for instance. However as the sound is very load it quickly enter in saturation. I'm trying reading i2s documentation how to get data directly in 8 bits (there is Philips and PCM 8bits) but for the moment I cannot figure how to implement. The i2s library changes a lot for a version to another.....

[piroposantosdev]

@philippedc I know this topic is a little old, but can you help me please? My inmp441 is not getting any audio. The http server is working, I'm able to surf to :83 port and play audio player but no audio is working from the mic. Do you know what can I do? When I tried your code it's just playing a noise and no detection from mic

[philippedc]

Which version of IDE and Expressif ?

Mine is working fine with AI thinker with: IDE version 1.8.16 with Expressif Sytems (ESP32) version 2.0.3
As I get many difficulties with INM441 settings, I understood I2S micro does not work with Expressif Sytems (ESP32) version 2.0.4 and after....